![]() The user that has the mount, has write access for the shared folder. The mount is to a file share on Synology. If I go into the mount with uid 1000 I have write access, but it didn't give me write access for Emby. Without the noperm only root had write access, so I figured this would help. dev/dri:/dev/dri # VAAPI/NVDEC/NVENC render nodes mnt/nas_video:/mnt/video # Media directory home/snip/emby:/config # Configuration directory mnt/m) Open /etc/fstab and add a line such as the following: M: /mnt/. I'm running Emby in a docker, the docker-compose is run from uid:1000: Mount Drives in a Persistent Manner Ensure the folder exists for the mount target (e.g. I've already checked File Permissions Guide for New Linux Users. And read multiple posts of people having similar problems, but that didn't help me so far. The strangest thing is that I did succeed in getting delete permissions: I can delete videos from Emby. It runs fine, except for the write permissions: nfo, srt, pictures are not saved after a refresh and an error is reported in the logs (attached) immediately after I try that. Here's two of the dozens of web pages I looked at, these yielded the most, but obviously not complete, results.I'm struggling with the write permissions for my Emby server. Switch to Task Settings tab and paste the sub interface configuration script: ip link remove eth0.10 ip link add link eth0 name eth0.10 type vlan id 10 ip link set dev eth0.10 up. Change User: to root, set Event: to Boot-Up. ![]() Mounting with a group id ( gid=1000) would be better, (and I'd put the mountpoints in /mnt/) but that's not working, so if I added a user, I'd be in trouble there. Control Panel -> Task Scheduler -> Create -> Triggered Task -> User Defined Script. I did try putting /sbin/mount.nfs in a few places in the syntax, leaving in the nfs reference (where cifs goes) but nothing would make the share available. Adding a colon after the IP of the server did not help and that didn't even get to the authentication part. But it doesn't, with the first error saying the share is not in host:dir format. There's no mount.smb option in sbin, but there is mount.nfs which could work, because my NAS has NFS turned on. The sharepoint appears, but opening as user yields an error that it can only be mounted as root, and opening as root says mount:/home/profile/Documents/nas: you may need a file type detail like /sbin/mount.(filetype) helper programīut I don't know where to place that in the syntax. smbcredentials, substituting credentials=filepath for the username and password. I'd prefer to use a file for credentials, so I made a file called. (I only have one user, and the mounts are in that home directory) I did try using gid instead of uid, but that did not work, so this only works for one user, I think. First, install Synology DiskStation Manager (DSM), which is Synology’s operating system, which you will be guided to do during the setup process: The system will warn you that all data will be wiped out from the hard drives that are installed, which is fine, considering that you have brand new drives mounted in the unit This is akin to having. You can use any letter that’s not currently used on your. In the text box next to Drive, select the drive letter that you’d like to use. I have tested this Script with Windows 10 Pro, it should work with Server 2012 R2 and Server. The Map Network Drive window will appear. MAP SYNOLOGY DRIVE WITH DIFFRENT USERNAME USING POWERSHELL. Next, click Map Network Drive in the Network group of the Computer tab. Search for Create and format hard disks partitions and click the top result to. I'm leaving this here in case I can help others with the same mounting issue. First, open File Explorer and then click This PC in the left-hand pane. Mount drive with Disk Management To use Disk Management to mount a drive on Windows 10, use these steps: Open Start. I had a lot of problems making that fstab file work, but finally I got it tweaked. However, that's labourious since I have several sharepoints to mount, therefore I want to mount using fstab for persistent mount, so I made this entry: //192.168.42.2/music /home/profile/Music/musicone cifs uid=linuxuser,username=sharepointuser,pass=sharepointpass 0 0 I can mount the shares using the following command in terminal: sudo mount -o uid=linuxusername,username=shareuser,pass=sharepass //192.168.1.2/music /home/profile/Music/musicone I'm using Ubuntu 20.4 with a Synology NAS that is accessible easily from Windows and Mac Mounting shares from Synology NAS persistent on boot up
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |